Frequently asked questions about band saw blades.
In case of broken teeth, broken blades or insufficient blade life, this page may help you easily solve your problem.
First, lay the broken blade flat on the ground and check the body and teeth for defects. You may find the solution to your cutting problem in one of the answers below.
Click on the problem you’ve identified and you’ll find a selection of the most common causes to review for a quick solution.
1. Premature and excessive tooth wear
- Feed pressure too light, increase it
- Reduce wheel speed
- Poor coolant flow
- Unsuitable emulsion
- Wrong tooth pitch, use a finer one
- Improper blade break-in
- Teeth pointing the wrong way relative to the cut, turn the blade around
2. The blade vibrates
- Increase or decrease wheel speed
- Dull vibration: increase blade tension
- Teeth too coarse for the workpiece being cut
- Vibration transmitted to the base: reduce cutting pressure
- High-frequency vibration: increase head descent rate
- Material not properly clamped
- Use a variable pitch or positive tooth pattern
3. The teeth break
- Teeth too coarse for the section being cut
- Material not properly clamped
- Unsuitable coolant
- Insufficient coolant
- Cutting pressure too high: check the chip
- Wheel speed too low
- Gullets overloaded with cut material
4. Cut surface too rough
- Choose a finer tooth pitch
- Increase wheel speed
- Reduce head descent rate
- Dose coolant more carefully
5. Premature blade breakage
- Blade thickness too great for the wheel diameter
- Blade guides too wide open at high speed
- Increase or decrease speed
- Check that wheels are free of defects
- Tooth pitch too coarse
- Blade tension too high: the blade, laid flat, lifts at the sides
- Head thrust too high: the blade back is shiny and burnished
- Guide inserts too narrow: the blade, laid flat, coils up like a spring. The narrower they are, the more it twists
- Insufficient coolant
6. Belly-shaped cuts
- Increase tension
- Move the blade guides closer to the cut
- Teeth too fine
- Reduce cutting pressure
7. Crooked cut
- Move blade guides closer to the cut
- Check that the workpiece support surface is level
- Check blade perpendicularity: if off, adjust the blade guides
- Tooth pitch too fine
- Broken or chipped teeth
- Increase speed
8. The blade is noisy on the thrust bearings
- Deburr or grind the back
- Check wheel alignment
- Check thrust bearing wear
- Imperfect weld
▶ 9. The blade bows positively
- Reduce cutting pressure
- Use coarser teeth to increase penetration
- Move blade guides closer to the cut
▶ 10. The blade bows negatively
- The back is pressing against the upper thrust guides: check clearance at the wheel contact points and thrust guides both with the blade stationary and running
- Check wheel alignment
11. Slow cutting rate, fine chips
- Increase wheel speed
- Increase cutting pressure
- Use coarser teeth
- Use suitable coolant
12. Premature loss of set
- Bend radius too tight for the blade
- Reduce wheel speed
- Increase coolant
13. The blade twists like a spring
- Blade too wide for the radius being cut
- Reduce cutting pressure
- Decrease blade tension
- Excessive guide-insert pressure: adjust it
- Move the blade guides closer to the cut
14. Chips weld to the tooth, chips too coarse
- Reduce cutting pressure
- Use a suitable, generous amount of coolant
- Check the efficiency of the brush that clears chips from the gullets
15. The blade is marked or bent on one side
- Check guide inserts for wear
- The inserts are pressing too hard on the blade back
- Check blade-guide alignment and perpendicularity
16. Burr or burnishing on the back
- Increase tension and adjust the blade guides
- Check the pressure and alignment of the thrust guides on the blade back
- Reduce cutting pressure
- Use a coarser tooth pitch
17. The cut workpiece is marked with black streaks
The back is rubbing against the cut:
- On the left: the left blade guide is out of alignment
- On the right: the right blade guide is out of square
Along the entire cut line:
- The blade guides are out of square
- Pressure is excessive
- Blade tension is low
- The teeth are too fine and are not clearing chips
- The wrong coolant is being used
If you are unable to resolve the issue, please complete the Customer Support Form and upload it via the Contact Form, selecting “Technical Support” from the “Request” menu.